Audi Forum banner
1 - 8 of 8 Posts

·
Registered
Joined
·
18 Posts
Discussion Starter · #1 ·
hello,
i'm trying to find where can connect power supply for led light putted under the foot position...
i've a tt mk2 without this light original, i've buy the light, connector and the pin...but i don't know the easier way to connect it (if is possible, i don't want to connect it in the roof light))

thanks :D
 

·
Registered
Joined
·
2 Posts
Reto fitting LED Lighting Pack or footwells alone is not that easy.
I did it on a previous MKII



Part number for footwell lights is 8J0 947 409 A (that appears to be a kit/or pair of, but check with your local dealer)
2 pin Connector for it is 4B0 971 832

Other part number for the QQ1 kit are..(not all are fitted to all markets!)
Puddle light 8J0 947 409
2 pin Connector for it is 4B0 971 832

if you want the bulb ones instead, this is the same as the one used for the bonnet/glovebox/boot etc
4B0 947 415 A
2 pin Connector for it is 4B0 971 832
Bulb N 017 753 2

Bonnet light
4B0 947 415 A
2 pin Connector for it is 4B0 971 832
Bulb N 017 753 2

Doors
Fibre optic
LHS 8J0 919 173
RHS 8J0 919 063
LED 4E0 919 063
Plasic holder got lever 8J0 837 019 B (black H77)

Door ends
8J0 947 409

Roof module trim with garage opener
8J0 947 133 L (trim 6PS is black)
Without
8J0 947 133 (trim 6PS is black)

Roof base plate (LED)
8J0 947 140 E


On the CEC detach the brown 11pin connctor (T11C)
Pin 9 for +
Pin 6 for -

You then need to change the coding via vagcom to enable the Menu
Then do the Coding change to enable the footwell lights, else if you dont they only work with the indicators.
 

·
Registered
Joined
·
18 Posts
Discussion Starter · #4 ·
thanks a lot rstt!!
at the moment i've do this as installation...
i've found the wire in the rooflight that give the negative for turn on the light when the door is open or when i give the command from the key and i've take the positive in the fuse box...
i think that i've to put at least a relays...

the cec is under the steering wheels where are all the relays on, correct? and the T11C is?

can you explain me better the procedure for the vagcom please?
 

·
Registered
Joined
·
2 Posts
You dont need to tap into anything else.

Harness i made.


Remove drivers side covering and glovebox - this big black box is the CEC



Run the cables as per above and refit trim






Recode CEC so you get a menu on the DIS




Enable footwell menu within the CEC using VAGCOM - put a tickbox in footwells
Go into the longcode
change byte 24 from 00 to 80

Use the menu to set the brightness.
 

·
Registered
Joined
·
2 Posts
Bonjour à tous.. J'ai actuellement un problème avec le codage de mes feux de pied, quand je fais le codage j'ai le menu dans le DIS mais j'ai les feux arrière gauche qui restent allumés sur l'indicateur de changement de voie... Si quelqu'un pouvait aidez moi ce serait sympa, c'est un tt 8j 3.2 de 2008, de plus je ne peux pas coder l'octet 24 car je n'ai rien dedans..
 
1 - 8 of 8 Posts
Top