Audi Forum banner

1 - 8 of 8 Posts

·
Registered
Joined
·
35 Posts
Discussion Starter #1


A: Speaker Connector
1 - N.C. (stands for emergency Connected)
2 - right in front +
3 - left in front +
4 - N.C.
5 - N.C.
6 - right in front -
7 - left in front -

B. EXT control Connector
1 - Most ring BREAK
2 - CDC NF GND
3 - V-signal (speed signal for 4B0.... RNS e)
4 - U14R-2
5 - K-LINE
6 - CDC DATA out
7 - BOSE pin
8 - CDC NF left IN
9 - CDC NF right IN
10 - U14 ST CDC
11 - CDC DATA IN
12 - CDC- DATA CLK

C: EXT control Connector
1 - MIC IN (-)
2 - RFSL
3 - LINE Out in front left
4 - MIC Out (-)
5 - LINE Out at the rear left
6 - TEL NF IN (-)
7 - MIC IN (+)
8 - LINE Out GND
9 - LINE Out in front right
10 - MIC Out (+)
11 - LINE Out right in the back
12 TEL NF IN (+)

D: Power Connector
9 - CAN h
10 - CAN l
11 - TEL
12 - Kl.31 (mass)
13 - U14 ST DSP (radio on)
14 - DWA GND
15 - Kl.30
16 - U14R-1

32 pin Connector:
1 - N.C.
2 - N.C.
3 - N.C.
4 - N.C.
5 - N.C.
6 - AUX NF IN right
7 - N.C.
8 - N.C.
9 - N.C.
10 - N.C.
11 - N.C.
12 - N.C.
13 - NF In right
14 - SHIELD GND
15 - In Sync
16 - IN-G
17 - N.C.
18 - N.C.
19 - N.C.
20 - N.C.
21 - AUX NF GND
22 - AUX NF In left
23 - N.C.
24 - N.C.
25 - N.C.
26 - N.C.
27 - N.C.
28 - NF-IN-GND
29 - NF In left
30 - RGBS IN GND
31 - IN-B
32 - IN-R
 

·
Registered
Joined
·
26 Posts
Check pins location

I ' ve found the rigth location for those cables :Tel-; Tel+; K dignose; c-bus H; c-bus L; mute Tel

but now I don't know where may I plug those: GND ; and 12V

where do they must are plug?
in that topic you can see my module and harness


 

·
Registered
Joined
·
8 Posts
Day and nite mode for RNS-E

Which pin connects to the RNS-E from the headlight switch to tell the RNS-E to go from Day mode display and then nite mode display (headlights turned on).

I am getting a loud buzzing sound when I turn my headlights on.
 

·
Registered
Joined
·
6,767 Posts
Which pin connects to the RNS-E from the headlight switch to tell the RNS-E to go from Day mode display and then nite mode display (headlights turned on).

I am getting a loud buzzing sound when I turn my headlights on.
No wire for that, it's a CAN message that tells the RNS-E whether or not the lights are on.
 
1 - 8 of 8 Posts
Top