BT interface - I cannot connect to it using VAG-COM

Are you using VAG-COM 5.10 and an original VAG-COM cable? Older versions and cheap replica cables don't work with the phone interface.

I am using a genuine VAG-COM cable from Ross-tech and the newest release of the software, so that's not where the problem is.

When I played with my OEM BT interface, I had similar issues. Using a HEX-CAN USB it took several attempts before it finally connected. I had also more success using the k-wire from the ODB plug instead of the K-wire from the radio plug (which is the L-wire or K2-wire).

I had this problem before.

But I finally log in while using the newest VAG-COM.

Would u like to try install the newest VAG-COM again?

kitora said:

I am using a genuine VAG-COM cable from Ross-tech and the newest release of the software, so that's not where the problem is.

Click to expand...

By newest do you mean 5.12? There have been problems with that release and Ross Tech have released 5.12-1.

Download that and try again.

If it still doesn't work then I would start by checking the K-line is connected to your BT module.

I do use VAG-COM 512-1 and even updated the firmware in my interface cable.

I'm absolutely sure the K-Line is connected, becaus when I pull the K-Line wire out of the connector I get a different message "No response from controller"

I initially pulled the K-Line from the climate control to the Navigation unit, and now I have connected the bluetooth box to the same wire. Could that be my problem ? (noise on the wire, or to many units on the same wire..)

I have to try the connecting serval times, but i get a connection!

Mütze

Did you have a wired Telematics system before the bluetooth

Could both boxes be trying to communicate?

Re: Did you have a wired Telematics system before the bluetooth

CZVT07 said:

Could both boxes be trying to communicate?

Click to expand...

I doubt it since they have different adresses. The Navigation unit has address 56 and the bluetooth box has address 77.

Besides I already tried disconnecting the navigation while trying to connect to the bluetooth box.

Try the 504, that is the only one that works for me the 510 512 512.1 will not comunicate withe the nav nor BT.

how do u updated the firmware in the interface cable?

I meant two TEL modules. An older wired TEL module under the pasenger seat and the new blue tooth one that you installed.

CZVT07 said:

I meant two TEL modules. An older wired TEL module under the pasenger seat and the new blue tooth one that you installed.

Click to expand...

Two devices connected and responding on the same address are definitely causing issues.

There is only the one telephone interface box. Trust me, I installed it myself...

BTW, it's in an Audi A2, and neither the RNS-E or Bluetooth box came with the car.

I still haven't found a solution, so any other ideas would be apreciated.

audi1 said:

how do u updated the firmware in the interface cable?

Click to expand...

It happens automatically when you first connect to the car using the new version of VAG-COM.

I'm having the same problem as the OP. I try to connect the module and its not conecting... and sometimes its giving me too much noise in the line (?) or too many communications errors. I used the kufatec cables and I think I connected everything correctly. Any suggestions?

I also ahve teh same problem, as i just posted with out seeing this(woops no search button)..

THough i did not connect teh k-line as the directions on here said dont bother..

I am glad the bluetooth does work though..Just no DIS screen so far and no phone book on my nokia which is wierd ot me..

If we should connect k-line to another source can someone post a diagram or picture so i can have my guy install it. He knows electronics, just not audi's..

Thanks alot
-Scott

I can now communicate with the module without any problems. I bought a new phone interface box 8P0-862-335-G. However the RNS-E still says there's no phone installed even though the BT works.

I need to play around with the coding a little bit to see if I can get a better result. My RNS-E SW version is 140, and in most of the topics I see in here people have SW version 110. Maybe that's causing me some problems ?

PS: The K-Line has to be connected to pin 15 on the phoneadapter. I used one of the spare wires in the kufatec cable and connected the other end on the K-Line pin on the back of the RNS-E. (the schematics on the back of the RNS-E will show you which pin it is :wink: )

Sw 0140 is the old Euro software without the phone features. To get the new features you will need to get a 2005_1 or newer Euro DVD with software 0330 or newer (current Euro DVD is 2006 with sw 0450). In the use you will need US sw 0110 to get the new features.

So, are you telling me that's the reason I cannot enter the phone book and see other features on my phone ? (Nokia 6230i)

These are the specs for my RNS-E:


SW: 0140
HW: H46
Map: M2N031204-EN0303