Audi Forum banner
1 - 14 of 14 Posts

·
Registered
Joined
·
81 Posts
Discussion Starter · #1 ·
Hi ppl;

I have this problem with my audi. I have the following parts with wrong coding
Bluetooth

8P0862335 D
soft coding :001811
Component FSE_255 BT H18 0050

Radio

8E=035192C
Soft coding: 0320000
Component Rns-e High Eu H99 0550

When i'm trying to recode with vagcom 512.4 with the ross usb cable, i put the values but nothing change, still with the same code.
Do i have to put a key in security access???

How can i recode this?
 

·
Registered
Joined
·
6,767 Posts
That RNS-E hardware is very interesting, H99 looks very much like a hacked unit. Anyway, 0320000 is not a valid software coding. If you have a non-Bose A4 B6, try 0301111, with Bose try 0309111. The phone interface doesn't support getting controlled from the RNS-E, so the coding you have is correct if you have a multifunction steering wheel and Audi radio in an A4 B6 and you want the ohone interface to understand voice commands in German.
 

·
Registered
Joined
·
81 Posts
Discussion Starter · #3 ·
Hi mate

H99 can't be hacked because this unit was buyed in Audi.
I don't have steering wheel, no voice command,i just want to have this working properly..

I'm trying to to put this value (0010307) but no luck too...any solution??
How do i reset the rns-e??

regards
 

·
Registered
Joined
·
81 Posts
Discussion Starter · #6 ·
Hi mate

Can you give a valid coding for this interface??
8P0862335 D??

I would like to try
I have the rns-e but i have this message "No phone connected" and i use my 6234 with the BT

Thanks
 

·
Registered
Joined
·
6,767 Posts
The D interface doesn't have Bluetooth, at least not if factory installed.

You can try to enable BT if you have the BT antenna installed by changing #77 channel 133 to 1, channel 134 to 0 and channel 135 contains the BT passcode to pair the phone. But even then you won't be able to dial using your RNS-E. For the RNS-E try 0xxx2xx, 0xxx3xx or 0xxx4xx after you got the phone paired.
 

·
Registered
Joined
·
81 Posts
Discussion Starter · #8 ·
Hi

I reach to recode to 0000702, it's a start..
Put the channel 133 = 1
Put the channel 134 = 0

But still have this...why??
VAG-COM Version: Release 512.4-UD

Control Module Part Number: 8P0 862 335 D
Component and/or Version: FSE_255x BT H18 0050
Software Coding: 0000702
Work Shop Code: WSC 06325
1 Fault Found:
00466 - Control Module for Steering Column Electronics (J527)
004 - No Signal/Communication - Intermittent


The rns-e i only reach to recode with 0309213
Should be 0309513...right??

Why i can't recode the rns-e to the 5 value??
 

·
Registered
Joined
·
6,767 Posts
Did you clear the faults and do they come back? Maybe they are left over from the initial install?

O doubt that you have the European Telematics installed, that was a Germany only thing a couple years ago. Try 2/3/4 and see what happens.
 

·
Registered
Joined
·
81 Posts
Discussion Starter · #10 ·
Hi
The 3 and 4 tell me to connect a phone, and mine is connected....
7 ask me to put the SIM
I put the 2 and i have the sinal strenght and when i use the phone the rns.e show 2 phones, but no phone list and worst than this, i heve a message in the rns-e
"When you receive a call the following......
I don't see the bluetooth icon..it's normal?
And the sound is crap...how do i resolve this??

Thanks
 

·
Registered
Joined
·
6,767 Posts
As I said, your RNS-E won't do anything with the phone if you keep the D interface. Get a newer interface or use the phone to dial and accept calls.
 

·
Registered
Joined
·
81 Posts
Discussion Starter · #12 ·
Hi mate, Thanks for helping me

In teh rns-e i can't put the "5" option, its teh Eu telematic, that's bacause th BT is D??
If yes and i change him , the newer version will accept?

Thanks
 

·
Registered
Joined
·
6,767 Posts
Get an C, F, M or H phone interface, code it 10722 and code the RNS-E 0309713 and all your problems will be history. if your phone is compatible with the phone interface of course.
 
1 - 14 of 14 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top