A Few US Bluetooth Project Questions.

1654 Views 13 Replies 5 Participants Last post by TeddyBGame, Sep 3, 2006

Stoodo

Discussion Starter · Nov 12, 2005

Just a few questions before I proceed... I read through the thread again, but I just want to double check some stuff.

1. grey Telephone Mute Connector D11
2. yellow K-Line D5
3. black with yellow stripe Can-Low D9
4. black with white stripe Can-High D10

The Red wire goes to the fuse box and the brown wire goes to ground?

What is the most functional coding at this point?

See less See more

Save

1 - 14 of 14 Posts

I got everything installed I guess.

I am able to pair with my Treo 650. I get sound through the speakers, but the RNS-E says Telephone Not Installed.

The only way I can talk to the telephone module with the VAG com is with the K line connected.

Save

b5retrofit

· #3 · Nov 12, 2005

Stoodo said:
I got everything installed I guess.

I am able to pair with my Treo 650. I get sound through the speakers, but the RNS-E says Telephone Not Installed.

The only way I can talk to the telephone module with the VAG com is with the K line connected.

Have you recoded the RNS-E yet? Once I coded mine for the proper telephone (I believe it is "6" for US) it switched from "Telephone Not Installed" to the voice commands list. Hope that helps

Save

Stoodo

Discussion Starter · #4 · Nov 12, 2005

Yeah, I was able to change to 6. Now it just says Use Cell Phone.

Save

AvanTTix

· #5 · Sep 3, 2006

i'm stuck w/ the "Telephone is not installed" screen too... the phone, a Motorola V557, has found the "Audi UHV 8237" bluetooth device... i can hear the phone connecting to the device through the speakers but that's about it... cannot do anything else...

my RNS-E is coded 0301611... software for the Nav is US110...

i got my harness through TeddyB...

thoughts?

Save

AudiA4B6US

· #6 · Sep 3, 2006

What is the part number of your phone interface? How is it coded?

Save

AvanTTix

· #7 · Sep 3, 2006

p/n: 8P0 862 335 B

coding: 0010777

i'm sitting in the car waiting for something to happen going to the archives but not having any luck...

whenever i check the coding the phone loses the bluetooth connection and get it back once i close the VAG module...

Save

AvanTTix

· #8 · Sep 3, 2006

well i just talked to Ted via the bluetooth module/RNS-E... yet i still have the "Telephone is not installed" screen... :roll:

Save

AvanTTix

· #9 · Sep 3, 2006

alright nevermind it's working now... i guess i needed to take the key off the ignition and let it sit there for a while... :roll:

Save

AudiA4B6US

· #10 · Sep 3, 2006

I have seen that after coding the phone interface for HIGH, the RNS-E needs a complete reset to detect that change. EIther locking the car for a couple of minutes, pressing RADIO+SETUP until it reboots or saving a value of 1 in channel 111 would do this.

Save

AvanTTix

· #11 · Sep 3, 2006

well i did turn the ignition on and off a couple of times, leaving it off for a while but i guess it needed the key to be removed from the ignition... i did try the "radio" & "set-up" combo but maybe i didn't hold them down long enough...

btw you did my emails, right?

Save

AudiA4B6US

· #12 · Sep 3, 2006

No, not recently. Which address did you send them to?

Save

AvanTTix

· #13 · Sep 3, 2006

doesn't surprise me as i got a couple of mail delivery delay notifications...

i'm using the "@sbcglobal.com" one...

Save

TeddyBGame

· #14 · Sep 3, 2006

AvantÃ©ix said:
alright nevermind it's working now... i guess i needed to take the key off the ignition and let it sit there for a while... :roll:

I told you it would recognize it.....and you doubt my harness-making-ability????? Dam you!!!....just kidding. Enjoy....and please post lots of pix of the install.

Save

1 - 14 of 14 Posts

This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.

Top Contributors this Month